General Thoughts: Engineering Studies (1 Viewer)

EpaX

Member
Joined
Oct 12, 2013
Messages
64
Gender
Male
HSC
2014
Uni Grad
2018
What did everyone get for MC? I got:
1)C
2)C
3)B
4)C
5)A
6)D
7)A
8)B
9)A
10)A
11)C
12)A
13)C
14)D
15)C
16)B
17)D
18)B
19)C
20)B
Q4 is definitely D, Q10 i think should be B, and Q14 should be B.
 

orcevalm

Member
Joined
Feb 25, 2013
Messages
54
Gender
Female
HSC
2014
What did everyone get for the Power question? the ferry one? I got o.something KW. its probs wrong
 

Shackleford

New Member
Joined
May 25, 2012
Messages
16
Location
Israel
Gender
Undisclosed
HSC
2014
Uni Grad
2004
Q20 should be A. Its a tricky question. You need to calculate 'y' which is 96, as the top half of the beam undergoes compressive stress. 'm' can be calculated by drawing up a basic SFD and BMD, which is 12kNm. Plug it into the bending stress formula, and it would be approximately 11.3MPa. The given area is useless information. Q10 answer:B would make some sense, as you'd average out the radii to get 16.5, which is the radius along the neutral axis. IDK about 14, I put down B for that.
 

chrisdelinet

Member
Joined
May 6, 2014
Messages
44
Gender
Male
HSC
2014
got that to but i think i got tension

for the truss question BC was 15kn in tension and DF was redundant
 

aDimitri

i'm the cook
Joined
Aug 22, 2013
Messages
505
Location
Blue Mountains
Gender
Male
HSC
2014
What did everyone get for MC? I got:
1)C
2)C
3)B
4)C
5)A
6)D
7)A
8)B
9)A
10)A
11)C
12)A
13)C
14)D
15)C
16)B
17)D
18)B
19)C
20)B
1)C
2)C
3)B
4)D
5)A
6)D
7)A
8)B
9)A
10)B
11)C
12)A
13)C
14)B (should be D, you were correct)
15)C
16)B
17)D
18)A (pretty sure this is wrong)
19)C
20)A
 

chrisdelinet

Member
Joined
May 6, 2014
Messages
44
Gender
Male
HSC
2014
Q20 should be A. Its a tricky question. You need to calculate 'y' which is 96, as the top half of the beam undergoes compressive stress. 'm' can be calculated by drawing up a basic SFD and BMD, which is 12kNm. Plug it into the bending stress formula, and it would be approximately 11.3MPa. The given area is useless information. Q10 answer:B would make some sense, as you'd average out the radii to get 16.5, which is the radius along the neutral axis. IDK about 14, I put down B for that.
Q20) B <--- darn this i put 154 into equation
Q10) B <--- just guessed really
Q14) D <--- B had a weird thing in the hole, therefore i reasoned it had to be D
 

EpaX

Member
Joined
Oct 12, 2013
Messages
64
Gender
Male
HSC
2014
Uni Grad
2018
14)B (should be D, you were correct)
But wouldn't that edge be visible for the flange, and it also wouldn't be sectioned because it's not on the cutting plane..?
 

Shackleford

New Member
Joined
May 25, 2012
Messages
16
Location
Israel
Gender
Undisclosed
HSC
2014
Uni Grad
2004
The power question would be different. You will need to calculate the new force as instead, you are pulling the boat up the plane which would constitute to a mix of frictional and weight pulling down the plane you'd need to overcome. This means you cannot use the answer from part (i) for this question. I think its approximately 4kW. For that friction boat question/power.
 
Last edited:

aDimitri

i'm the cook
Joined
Aug 22, 2013
Messages
505
Location
Blue Mountains
Gender
Male
HSC
2014
The power question would be different. You will need to calculate the new force as instead, you are pulling the boat up the plane which would constitute to a mix of frictional and weight pulling down the plane you'd need to overcome. This means you cannot use the answer from part (i) for this question. I think its approximately 4kW.
the F in part i is overcoming the weight.
 

chrisdelinet

Member
Joined
May 6, 2014
Messages
44
Gender
Male
HSC
2014
omg i spent so long in the exam wondering why equilibrium was being violated :'(
i did the calculations and ended up with zero, therefore to double check i looked at the joint F (i believe that it was this joint on the top of my head) and it had three members there. I could not close the force polygon if i tried to include all three members, but i could by omitting DF, therefore im quite certain its redundant. (if you wanted my thought process =D)
 

Shackleford

New Member
Joined
May 25, 2012
Messages
16
Location
Israel
Gender
Undisclosed
HSC
2014
Uni Grad
2004
No it said to prevent it from slipping. So friction would be helping you to prevent the boat from sliding down the plane.
 

chrisdelinet

Member
Joined
May 6, 2014
Messages
44
Gender
Male
HSC
2014
What did everyone do for that centre of mass question? i used moments from the nose of the plane, but don't know if it was correct or not.
 

mirachael

Active Member
Joined
Dec 30, 2013
Messages
115
Gender
Male
HSC
2014
What did everyone get for MC? I got:
1)C
2)C
3)B
4)C
5)A
6)D
7)A
8)B
9)A
10)A
11)C
12)A
13)C
14)D
15)C
16)B
17)D
18)B
19)C
20)B
Whoops typo I got B for 10. And shit didn't see the compression part for 20. Well there goes my state rank.
 

mirachael

Active Member
Joined
Dec 30, 2013
Messages
115
Gender
Male
HSC
2014
18)A (pretty sure this is wrong)
0.16 (A) is what you get when you divide Load over effort. However, the machine isn't necessarily 100% efficient so VR!=MA so you have to find VR on its own. This is basically (2*170/700)*(20/50)=0.19 which is B
 

Users Who Are Viewing This Thread (Users: 0, Guests: 1)

Top